SLA 3D Printing Malaysia Detailed Resin Plastic


e are proud to present to you, Detailed Resin Plastic, a 3D printing material that is able to capture an extreme level of detail with smooth surface finishing.

High Detailed Resin material is constructed from UV-sensitive liquid resin hardened by UV laser, from bottom to top. Stereolithography SLA 3D Printing process require supports for cavities and overhang regions. The required supports will be automatically generated by software and later manually removed. Hence, freedom of design is limited. At ZELTA3D, we provide Stereolithography SLA 3D Printing for white or transparent part.

  • White SLA 3D Printing Service in Malaysia
  • White SLA 3D Printing Black Panther
  • White SLA 3D Printing Architecture Model
  • White SLA 3D Printing Train Model

Material Overview


Suitable for:

  • Visual prototypes and large models.
  • Parts that requires great surface quality and fine details.
  • Spray painting.
  • Parts with limited functionality.
  • Low-volume production.
  • Creating masters for casting (e.g. Vacuum, investment casting).

Lead Time

Standard Lead Time:
ship in about 4 business days

Expedited Lead Time:
ship in about 3 business days


Build Size: 530L x 450W x 530H mm

Minimum Wall Thickness: 1mm (may vary)

Minimum Detail: 0.5 mm

Clearance for fitting:
0.1mm (tight fit) – 0.3mm (loose fit)

Estimated Accuracy:
±0.2% (with a lower limit of ±0.2 mm)


  • Excellent Surface Details. Good Accuracy
  • Smooth parts perfect for painting
  • Almost non-visible 3D Print layer lines
  • Quality printing at economical rate
  • Large parts up to 70cm

Suitable for prototypes with limited functionality.
(i.e. simple assembly and low thermal resistance)

SLA 3D Printing Material is suitable if you require a big, high quality and economical part where the material technical properties aren’t critical. Best used for intricate parts and high-quality visual prototypes when form, fit and test is applicable.

Technical Data

Tensile Strength: 68 MPa (ASTM D638)
Tensile Modulus: 2300 MPa (ASTM D638)
Elongation at break: 6%
(ASTM D638)
Flexural Strength: 65 MPa (ASTM D790)
Flexural Modulus: 2000 MPa (ASTM D790)
Izod impact notched: 23J/m
Heat Deflection Temperature (0.45MPa): 45°C
Heat Deflection Temperature (1.82MPa): 40°C
Shore Hardness: 80D
*Users should conduct their own testing to determine actual results. Values to be used for reference only.

Design Guidelines

Wall Thickness

Minimum wall thickness: 1mm (may vary depending on part dimension)

To ensure that your model is 3D printable, we would recommend a minimum wall thickness of 1mm. However, we recommend that you increase the wall thickness of your model as your design gets larger in scale. Designing your models too thin may result in your 3D printed part being too fragile for handling, prone to warping and may break easily.

Sufficient wall thickness is crucial to ensure that your models make it through printing and post processing.

Embossed & Engraved Details

For embossed details, we recommend a minimum thickness of 0.5mm and a height of 0.5mm for your text.

For engraved details, we recommend a minimum thickness of 0.5mm and a minimum depth of 0.5mm.


Clearance is the space between two objects, allowing one or both of them to have a certain degree of freedom of movement relative to the other. We would recommend 0.1mm for tight fit, 0.2mm for standard fit and 0.3mm for loose fit. You are advise to test out several iterations if you wish to attain a perfect fit.

Hollowing Model

As much as possible we would recommend to hollow out solid models. Majority of the time, producing your 3D printed part in full solid may not be necessary. By doing so, you can reduce cost and avoid shrinkage issues in thicker regions. Recommended wall thickness 2-3mm (for model below 35cm). 4-5mm wall thickness is recommended for model between 35cm to 70cm)

Even after hollowing your model there will still be 3D printing material trapped in the interior. To avoid this, you can design “escape holes” to your model so that the excess material can be drained. Escape holes are recommended to be at least 4mm in diameter and beyond 8mm for large model. For large model, adding a single escape hole will not allow the excess material to be drained fully. Hence we recommend multiple escape holes to be added.

Large Flat Plane

Designing large flat planes will cause will model to deform or warp. To avoid this, we would advice to avoid designing models with large flat planes.

Strengthening Model

Often when designing your model, it is a good practice to include ribs and gussets to improve the strength and stiffness of your model.

Multiple Part File

Multiple part in a file is a common reason for us to reject an order or cause delay for us to process your order. When you need more than one model to be printed, simply export the separate models individually and send it in to us for printing or quoting.

Design for Transparency

When designing your transparent model, do ensure that both internal and external walls are expose and easily reach to attain a higher transparency for your printed part.

Clear varnish have to be applied internally and externally for your models to attain a good transparency. If either side of the wall cannot be reached by spray painting, it will affect the transparency of your model.

*Please take note that having very thick walls could also reduce the transparency in your model!

Get instant quote

Use your Malaysia student email for 15% discount